The Ermenrich Ping MK40 digital clamp meter measures not only alternating current, but also direct current in addition to 6 other parameters: voltage (DC and AC), resistance, frequency, capacity, duty cycle and temperature. It includes additional features that make it the indispensable caliper to solve the problems of amateur and professional users.
The measurements are carried out using the true RMS value and the results are more accurate. There is a low frequency filter (LPF) that isolates several harmonics, increasing the reliability of measurements. To compensate for residual magnetization during direct current measurement, it can be set to zero (DCA Zero).
Continuity mode is one of the basic operating modes of current clamp meters. Helps identify open circuits or short circuits. You can also test diodes to identify faults. In NCV (non-contact high voltage detection) mode, the device detects hidden wiring and sockets that contain electricity.
The LowZ function is not found in all devices. When used, the digital clamp meter switches to low impedance mode, i.e. very low resistance. This greatly increases the accuracy of voltage measurements, which may drop due to interference from nearby electrical networks or devices. In LowZ mode, the influence of interference on the measurement accuracy is minimized.
The device operates on standard batteries. It features a built-in flashlight for working in dark environments and a data hold function that allows you to access on-screen readings after measurements, freezing the result on the screen.
Key features:
- Safe measurement of AC and DC current without breaking the circuit
- Functions of voltmeter (DC and AC voltage measurement), ohmmeter, frequency meter, capacitance meter , duty cycle meter, thermocouple sensor
- Low impedance (LowZ) voltmeter function, low resistance voltage measurement
- Low pass filter, DC zeroing and true RMS value calculation for better reliability of measurements
- Freezing of readings on the screen, data freeze function
The kit includes:
- Current clamp
- Test probes
- Box
- User manual and warranty certificate
| Brand | Ermenrich |
| Warranty | 5 лет |
| EAN | 5905555017471 |
| Package size (WxDxH) | 22x11x4 cm |
| Shipping weight | 0.44 kg |
| Select measurement limit | auto, manual |
| Basic Functions | voltmeter, ammeter, ohmmeter, electrical capacitance meter, frequency meter, duty cycle meter, thermocouple |
| DC voltage measurement limit | 600 mV/6 V/60 V/600 V: error ±(0.5%+5) |
| AC voltage measurement limit | 4/40/400/600 V; 6/60/600/600 V: error ±(0.8%+5) |
| DC current measurement limit | 60/600 A: error ±(2.5%+5) |
| AC current measurement limit | 60/600 A: error ±(2.5%+5 ) |
| Resistance measurement limit | 600 Ω/6 kΩ/60 kΩ/600 kΩ/6 MΩ/60 MΩ: error ±(1.0 %+5) |
| Capacitance measurement limit | 4 nF/40 nF/400 nF/4 μF/40 μF/400 μF: error ±( 4.0%+5) |
| Frequency measurement limits | 10 Hz/100 Hz/1 kHz/10 kHz/100 kHz/1 MHz /10 MHz: error ±(1.0%+3) |
| Duty cycle measurement range | 1–99%: error ±( 3.0%+3) |
| Diode tester | yes |
| Non-contact phase tester ( NCV) | yes |
| True RMS value | yes |
| Function hold (fixed measurement) | yes |
| Limit value function (Min/Max) | yes |
| DCA Zero | yes |
| Low pass filter (LPF) | yes |
| Low impedance voltage measurement (LowZ) | yes |
| Overvoltage category | CAT III 600 V |
| Maximum display value | 6000 |
| Display backlight | yes |
| Flashing light | yes |
| Safety standards | EN61010-1,-2-030; EN61010-2-033; EN61326-1 |
| Operating temperature range, °C | -40 — 1000 |
| Test continuity | yes |
| Power supply | 2 AAA batteries (not included) |
| Low battery indicator | yes |
| Auto power off | yes |
